RFC 9414 INFORMATIONAL SECURITY · PROTOCOL DESIGN · HISTORY

Unfortunate History of Transient Numeric Identifiers

How weak choices of transient identifiers kept producing the same failures for more than thirty years.

On rfc-editor.org ↗
PUBLISHED
July 2023
AUTHORS
F. Gont, I. Arce
STREAM
IRTF
IP IDENTIFICATION FIELD VALUES
65,536
RFC 793 ISN COUNTER RATE
Incremented by 1 roughly every 4 microseconds
YEARS FROM ISN ATTACK TO RFC 793 UPDATE
27 years
DNS ID SIZE
16 bits
NTP REFERENCE ID SIZE
32 bits
RECOMMENDED EPHEMERAL PORT RANGE
1024 to 65535
DOI
10.17487/RFC9414

RFC text

Contents
Original text · RFC Editor View on rfc-editor.org ↗
Internet Research Task Force (IRTF)                              F. Gont
Request for Comments: 9414                                  SI6 Networks
Category: Informational                                          I. Arce
ISSN: 2070-1721                                                Quarkslab
                                                               July 2023


          Unfortunate History of Transient Numeric Identifiers

Abstract

   This document analyzes the timeline of the specification and
   implementation of different types of "transient numeric identifiers"
   used in IETF protocols and how the security and privacy properties of
   such protocols have been affected as a result of it.  It provides
   empirical evidence that advice in this area is warranted.  This
   document is a product of the Privacy Enhancements and Assessments
   Research Group (PEARG) in the IRTF.

Status of This Memo

   This document is not an Internet Standards Track specification; it is
   published for informational purposes.

   This document is a product of the Internet Research Task Force
   (IRTF).  The IRTF publishes the results of Internet-related research
   and development activities.  These results might not be suitable for
   deployment.  This RFC represents the consensus of the Privacy
   Enhancements and Assessments Research Group of the Internet Research
   Task Force (IRTF).  Documents approved for publication by the IRSG
   are not candidates for any level of Internet Standard; see Section 2
   of RFC 7841.

   Information about the current status of this document, any errata,
   and how to provide feedback on it may be obtained at
   https://www.rfc-editor.org/info/rfc9414.

Copyright Notice

   Copyright (c) 2023 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (https://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.

Table of Contents

   1.  Introduction
   2.  Terminology
   3.  Threat Model
   4.  Issues with the Specification of Transient Numeric Identifiers
     4.1.  IPv4/IPv6 Identification
     4.2.  TCP Initial Sequence Numbers (ISNs)
     4.3.  IPv6 Interface Identifiers (IIDs)
     4.4.  NTP Reference IDs (REFIDs)
     4.5.  Transport-Protocol Ephemeral Port Numbers
     4.6.  DNS ID
   5.  Conclusions
   6.  IANA Considerations
   7.  Security Considerations
   8.  References
     8.1.  Normative References
     8.2.  Informative References
   Acknowledgements
   Authors' Addresses

1.  Introduction

   Networking protocols employ a variety of transient numeric
   identifiers for different protocol objects, such as IPv4 and IPv6
   Identification values [RFC0791] [RFC8200], IPv6 Interface Identifiers
   (IIDs) [RFC4291], transport-protocol ephemeral port numbers
   [RFC6056], TCP Initial Sequence Numbers (ISNs) [RFC9293], NTP
   Reference IDs (REFIDs) [RFC5905], and DNS IDs [RFC1035].  These
   identifiers typically have specific requirements (e.g., uniqueness
   during a specified period of time) that must be satisfied such that
   they do not result in negative interoperability implications and an
   associated failure severity when such requirements are not met
   [RFC9415].

      |  NOTE: Some documents refer to the DNS ID as the DNS "Query ID"
      |  or "TxID".

   For more than 30 years, a large number of implementations of IETF
   protocols have been subject to a variety of attacks, with effects
   ranging from Denial of Service (DoS) or data injection to information
   leakages that could be exploited for pervasive monitoring [RFC7258].
   The root cause of these issues has been, in many cases, the poor
   selection of transient numeric identifiers in such protocols, usually
   as a result of insufficient or misleading specifications.  While it
   is generally trivial to identify an algorithm that can satisfy the
   interoperability requirements of a given transient numeric
   identifier, empirical evidence exists that doing so without
   negatively affecting the security and/or privacy properties of the
   aforementioned protocols is prone to error.

   For example, implementations have been subject to security and/or
   privacy issues resulting from:

   *  predictable IPv4 or IPv6 Identification values (e.g., see
      [Sanfilippo1998a], [RFC6274], and [RFC7739]),

   *  predictable IPv6 IIDs (e.g., see [RFC7217], [RFC7707], and
      [RFC7721]),

   *  predictable transport-protocol ephemeral port numbers (e.g., see
      [RFC6056] and [Silbersack2005]),

   *  predictable TCP Initial Sequence Numbers (ISNs) (e.g., see
      [Morris1985], [Bellovin1989], and [RFC6528]),

   *  predictable initial timestamps in TCP timestamps options (e.g.,
      see [TCPT-uptime] and [RFC7323]), and

   *  predictable DNS IDs (see, e.g., [Schuba1993] and [Klein2007]).

   Recent history indicates that, when new protocols are standardized or
   new protocol implementations are produced, the security and privacy
   properties of the associated transient numeric identifiers tend to be
   overlooked, and inappropriate algorithms to generate such identifiers
   are either suggested in the specifications or selected by
   implementers.  As a result, advice in this area is warranted.

   This document contains a non-exhaustive timeline of the specification
   and vulnerability disclosures related to some sample transient
   numeric identifiers, including other work that has led to advances in
   this area.  This analysis indicates that:

   *  vulnerabilities associated with the inappropriate generation of
      transient numeric identifiers have affected protocol
      implementations for an extremely long period of time,

   *  such vulnerabilities, even when addressed for a given protocol
      version, were later reintroduced in new versions or new
      implementations of the same protocol, and

   *  standardization efforts that discuss and provide advice in this
      area can have a positive effect on IETF specifications and their
      corresponding implementations.

   While it is generally possible to identify an algorithm that can
   satisfy the interoperability requirements for a given transient
   numeric identifier, this document provides empirical evidence that
   doing so without negatively affecting the security and/or privacy
   properties of the corresponding protocols is nontrivial.  Other
   related documents ([RFC9415] and [RFC9416]) provide guidance in this
   area, as motivated by the present document.

   This document represents the consensus of the Privacy Enhancements
   and Assessments Research Group (PEARG).

2.  Terminology

   Transient Numeric Identifier:
      A data object in a protocol specification that can be used to
      definitely distinguish a protocol object (a datagram, network
      interface, transport-protocol endpoint, session, etc.) from all
      other objects of the same type, in a given context.  Transient
      numeric identifiers are usually defined as a series of bits and
      represented using integer values.  These identifiers are typically
      dynamically selected, as opposed to statically assigned numeric
      identifiers (e.g., see [IANA-PROT]).  We note that different
      transient numeric identifiers may have additional requirements or
      properties depending on their specific use in a protocol.  We use
      the term "transient numeric identifier" (or simply "numeric
      identifier" or "identifier" as short forms) as a generic term to
      refer to any data object in a protocol specification that
      satisfies the identification property stated above.

   The terms "constant IID", "stable IID", and "temporary IID" are to be
   interpreted as defined in [RFC7721].

3.  Threat Model

   Throughout this document, we do not consider on-path attacks.  That
   is, we assume the attacker does not have physical or logical access
   to the system(s) being attacked and that the attacker can only
   observe traffic explicitly directed to the attacker.  Similarly, an
   attacker cannot observe traffic transferred between the sender and
   the receiver(s) of a target protocol but may be able to interact with
   any of these entities, including by, e.g., sending any traffic to
   them to sample transient numeric identifiers employed by the target
   hosts when communicating with the attacker.

   For example, when analyzing vulnerabilities associated with TCP
   Initial Sequence Numbers (ISNs), we consider the attacker is unable
   to capture network traffic corresponding to a TCP connection between
   two other hosts.  However, we consider the attacker is able to
   communicate with any of these hosts (e.g., establish a TCP connection
   with any of them) to, e.g., sample the TCP ISNs employed by these
   hosts when communicating with the attacker.

   Similarly, when considering host-tracking attacks based on IPv6
   Interface Identifiers, we consider an attacker may learn the IPv6
   address employed by a victim host if, e.g., the address becomes
   exposed as a result of the victim host communicating with an
   attacker-operated server.  Subsequently, an attacker may perform
   host-tracking by probing a set of target addresses composed by a set
   of target prefixes and the IPv6 Interface Identifier originally
   learned by the attacker.  Alternatively, an attacker may perform
   host-tracking if, e.g., the victim host communicates with an
   attacker-operated server as it moves from one location to another,
   thereby exposing its configured addresses.  We note that none of
   these scenarios require the attacker observe traffic not explicitly
   directed to the attacker.

4.  Issues with the Specification of Transient Numeric Identifiers

   While assessing IETF protocol specifications regarding the use of
   transient numeric identifiers, we have found that most of the issues
   discussed in this document arise as a result of one of the following
   conditions:

   *  protocol specifications that under specify their transient numeric
      identifiers

   *  protocol specifications that over specify their transient numeric
      identifiers

   *  protocol implementations that simply fail to comply with the
      specified requirements

   A number of IETF protocol specifications under specified their
   transient numeric identifiers, thus leading to implementations that
   were vulnerable to numerous off-path attacks.  Examples of them are
   the specification of TCP local ports in [RFC0793] or the
   specification of the DNS ID in [RFC1035].

      |  NOTE: The TCP local port in an active OPEN request is commonly
      |  known as the "ephemeral port" of the corresponding TCP
      |  connection [RFC6056].

   On the other hand, there are a number of IETF protocol specifications
   that over specify some of their associated transient numeric
   identifiers.  For example, [RFC4291] essentially overloads the
   semantics of IPv6 Interface Identifiers (IIDs) by embedding link-
   layer addresses in the IPv6 IIDs when the interoperability
   requirement of uniqueness could be achieved in other ways that do not
   result in negative security and privacy implications [RFC7721].
   Similarly, [RFC2460] suggests the use of a global counter for the
   generation of Identification values when the interoperability
   requirement of uniqueness per {IPv6 Source Address, IPv6 Destination
   Address} could be achieved with other algorithms that do not result
   in negative security and privacy implications [RFC7739].

   Finally, there are protocol implementations that simply fail to
   comply with existing protocol specifications.  For example, some
   popular operating systems still fail to implement transport-protocol
   ephemeral port randomization, as recommended in [RFC6056], or TCP
   Initial Sequence Number randomization, as recommended in [RFC9293].

   The following subsections document the timelines for a number of
   sample transient numeric identifiers that illustrate how the problem
   discussed in this document has affected protocols from different
   layers over time.  These sample transient numeric identifiers have
   different interoperability requirements and failure severities (see
   Section 6 of [RFC9415]), and thus are considered to be representative
   of the problem being analyzed in this document.

4.1.  IPv4/IPv6 Identification

   This section presents the timeline of the Identification field
   employed by IPv4 (in the base header) and IPv6 (in Fragment Headers).
   The reason for presenting both cases in the same section is to make
   it evident that, while the Identification value serves the same
   purpose in both protocols, the work and research done for the IPv4
   case did not influence IPv6 specifications or implementations.

   The IPv4 Identification is specified in [RFC0791], which specifies
   the interoperability requirements for the Identification field, i.e.,
   the sender must choose the Identification field to be unique for a
   given {Source Address, Destination Address, Protocol} for the time
   the datagram (or any fragment of it) could be alive in the Internet.
   It suggests that a sending protocol module may keep "a table of
   Identifiers, one entry for each destination it has communicated with
   in the last maximum packet lifetime for the [I]nternet", and it also
   suggests that "since the Identifier field allows 65,536 different
   values, hosts may be able to simply use unique identifiers
   independent of destination".  The above has been interpreted numerous
   times as a suggestion to employ per-destination or global counters
   for the generation of Identification values.  While [RFC0791] does
   not suggest any flawed algorithm for the generation of Identification
   values, the specification omits a discussion of the security and
   privacy implications of predictable Identification values.  This
   resulted in many IPv4 implementations generating predictable
   Identification values by means of a global counter, at least at some
   point in time.

   The IPv6 Identification was originally specified in [RFC1883].  It
   serves the same purpose as its IPv4 counterpart, but rather than
   being part of the base header (as in the IPv4 case), it is part of
   the Fragment Header (which may or may not be present in an IPv6
   packet).  Section 4.5 of [RFC1883] states that the Identification
   must be different than that of any other fragmented packet sent
   recently (within the maximum likely lifetime of a packet) with the
   same Source Address and Destination Address.  Subsequently, it notes
   that this requirement can be met by means of a wrap-around 32-bit
   counter that is incremented each time a packet must be fragmented and
   that it is an implementation choice whether to use a global or a per-
   destination counter.  Thus, the specification of the IPv6
   Identification is similar to that of the IPv4 case, with the only
   difference that, in the IPv6 case, the suggestions to use simple
   counters is more explicit.  [RFC2460] is the first revision of the
   core IPv6 specification and maintains the same text for the
   specification of the IPv6 Identification field.  [RFC8200], the
   second revision of the core IPv6 specification, removes the
   suggestion from [RFC2460] to use a counter for the generation of IPv6
   Identification values and points to [RFC7739] for sample algorithms
   for their generation.

   September 1981:
      [RFC0791] specifies the interoperability requirements for the IPv4
      Identification but does not perform a vulnerability assessment of
      this transient numeric identifier.

   December 1995:
      [RFC1883], the first specification of the IPv6 protocol, is
      published.  It suggests that a counter be used to generate the
      IPv6 Identification values and notes that it is an implementation
      choice whether to maintain a single counter for the node or
      multiple counters (e.g., one for each of the node's possible
      Source Addresses, or one for each active {Source Address,
      Destination Address} set).

   December 1998:
      [Sanfilippo1998a] finds that predictable IPv4 Identification
      values (as generated by most popular implementations) can be
      leveraged to count the number of packets sent by a target node.
      [Sanfilippo1998b] explains how to leverage the same vulnerability
      to implement a port-scanning technique known as "idle scan".  A
      tool that implements this attack is publicly released.

   December 1998:
      [RFC2460], a revision of the IPv6 specification, is published,
      obsoleting [RFC1883].  It maintains the same specification of the
      IPv6 Identification field as its predecessor [RFC1883].

   December 1998:
      OpenBSD implements randomization of the IPv4 Identification field
      [OpenBSD-IPv4-ID].

   November 1999:
      [Sanfilippo1999] discusses how to leverage predictable IPv4
      Identification values to uncover the rules of a number of
      firewalls.

   September 2002:
      [Fyodor2002] documents the implementation of the "idle scan"
      technique in the popular Network Mapper (nmap) tool.

   November 2002:
      [Bellovin2002] explains how the IPv4 Identification field can be
      exploited to count the number of systems behind a NAT.

   October 2003:
      OpenBSD implements randomization of the IPv6 Identification field
      [OpenBSD-IPv6-ID].

   December 2003:
      [Zalewski2003] explains a technique to perform TCP data injection
      attacks based on predictable IPv4 Identification values, which
      requires less effort than TCP injection attacks performed with
      bare TCP packets.

   January 2005:
      [Silbersack2005] discusses shortcomings in a number of techniques
      to mitigate predictable IPv4 Identification values.

   October 2007:
      [Klein2007] describes a weakness in the pseudorandom number
      generator (PRNG) in use for the generation of IP Identification
      values by a number of operating systems.

   June 2011:
      [Gont2011] describes how to perform idle scan attacks in IPv6.

   November 2011:
      Linux mitigates predictable IPv6 Identification values
      [RedHat2011] [SUSE2011] [Ubuntu2011].

   December 2011:
      [draft-gont-6man-predictable-fragment-id-00] describes the
      security implications of predictable IPv6 Identification values
      and possible mitigations.  This document has the intended status
      of "Standards Track", with the intention to formally update
      [RFC2460] to introduce security and privacy requirements on the
      generation of IPv6 Identification values.

   May 2012:
      [Gont2012] notes that some major IPv6 implementations still employ
      predictable IPv6 Identification values.

   March 2013:
      The 6man WG adopts [draft-gont-6man-predictable-fragment-id-03]
      but changes the track to "BCP" (while still formally updating
      [RFC2460]), posting the resulting document as
      [draft-ietf-6man-predictable-fragment-id-00].

   June 2013:
      A patch to incorporate support for IPv6-based idle scans in nmap
      is submitted [Morbitzer2013].

   December 2014:
      The 6man WG changes the intended status of
      [draft-ietf-6man-predictable-fragment-id-01] to "Informational"
      and posts it as [draft-ietf-6man-predictable-fragment-id-02].  As
      a result, it no longer formally updates [RFC2460], and security
      and privacy requirements on the generation of IPv6 Identification
      values are eliminated.

   June 2015:
      [draft-ietf-6man-predictable-fragment-id-08] notes that some
      popular host and router implementations still employ predictable
      IPv6 Identification values.

   February 2016:
      [RFC7739] (based on [draft-ietf-6man-predictable-fragment-id-10])
      analyzes the security and privacy implications of predictable IPv6
      Identification values and provides guidance for selecting an
      algorithm to generate such values.  However, being published as an
      "Informational" RFC, it does not formally update [RFC2460] and
      does not introduce security and privacy requirements on the
      generation of IPv6 Identification values.

   June 2016:
      [draft-ietf-6man-rfc2460bis-05], a draft revision of [RFC2460],
      removes the suggestion from [RFC2460] to use a counter for the
      generation of IPv6 Identification values but does not perform a
      vulnerability assessment of the generation of IPv6 Identification
      values and does not introduce security and privacy requirements on
      the generation of IPv6 Identification values.

   July 2017:
      [draft-ietf-6man-rfc2460bis-13] is finally published as [RFC8200],
      obsoleting [RFC2460] and pointing to [RFC7739] for sample
      algorithms for the generation of IPv6 Identification values.
      However, it does not introduce security and privacy requirements
      on the generation of IPv6 Identification values.

   October 2019:
      [IPID-DEV] notes that the IPv6 Identification generators of two
      popular operating systems are flawed.

4.2.  TCP Initial Sequence Numbers (ISNs)

   [RFC0793] suggests that the choice of the ISN of a connection is not
   arbitrary but aims to reduce the chances of a stale segment from
   being accepted by a new incarnation of a previous connection.
   [RFC0793] suggests the use of a global 32-bit ISN generator that is
   incremented by 1 roughly every 4 microseconds.  However, as a matter
   of fact, protection against stale segments from a previous
   incarnation of the connection is enforced by preventing the creation
   of a new incarnation of a previous connection before 2*MSL has passed
   since a segment corresponding to the old incarnation was last seen
   (where "MSL" is the "Maximum Segment Lifetime" [RFC0793]).  This is
   accomplished by the TIME-WAIT state and TCP's "quiet time" concept
   (see Appendix B of [RFC1323]).  Based on the assumption that ISNs are
   monotonically increasing across connections, many stacks (e.g.,
   4.2BSD-derived) use the ISN of an incoming SYN segment to perform
   "heuristics" that enable the creation of a new incarnation of a
   connection while the previous incarnation is still in the TIME-WAIT
   state (see p. 945 of [Wright1994]).  This avoids an interoperability
   problem that may arise when a node establishes connections to a
   specific TCP end-point at a high rate [Silbersack2005].

   The interoperability requirements for TCP ISNs are probably not as
   clearly spelled out as one would expect.  Furthermore, the suggestion
   of employing a global counter in [RFC0793] negatively affects the
   security and privacy properties of the protocol.

   September 1981:
      [RFC0793] suggests the use of a global 32-bit ISN generator, whose
      lower bit is incremented roughly every 4 microseconds.  However,
      such an ISN generator makes it trivial to predict the ISN that a
      TCP implementation will use for new connections, thus allowing a
      variety of attacks against TCP.

   February 1985:
      [Morris1985] is the first to describe how to exploit predictable
      TCP ISNs for forging TCP connections that could then be leveraged
      for trust relationship exploitation.

   April 1989:
      [Bellovin1989] discusses the security considerations for
      predictable ISNs (along with a range of other protocol-based
      vulnerabilities).

   January 1995:
      [Shimomura1995] reports a real-world exploitation of the
      vulnerability described in [Morris1985] ten years before (in
      1985).

   May 1996:
      [RFC1948] is the first IETF effort, authored by Steven Bellovin,
      to address predictable TCP ISNs.  However, [RFC1948] does not
      formally update [RFC0793].  Note: The same concept specified in
      this document for TCP ISNs was later proposed for TCP ephemeral
      ports [RFC6056], TCP Timestamps, and eventually even IPv6
      Interface Identifiers [RFC7217].

   July 1996:
      OpenBSD implements TCP ISN randomization based on random
      increments (please see Appendix A.2 of [RFC9415])
      [OpenBSD-TCP-ISN-I].

   December 2000:
      OpenBSD implements TCP ISN randomization using simple
      randomization (please see Section 7.1 of [RFC9415])
      [OpenBSD-TCP-ISN-R].

   March 2001:
      [Zalewski2001] provides a detailed analysis of statistical
      weaknesses in some TCP ISN generators and includes a survey of the
      algorithms in use by popular TCP implementations.  Vulnerability
      advisories [USCERT2001] were released regarding statistical
      weaknesses in some TCP ISN generators, affecting popular TCP
      implementations.  Other vulnerability advisories on the same
      vulnerability, such as [CERT2001], were published later on.

   March 2002:
      [Zalewski2002] updates and complements [Zalewski2001].  It
      concludes that "while some vendors [...] reacted promptly and
      tested their solutions properly, many still either ignored the
      issue and never evaluated their implementations, or implemented a
      flawed solution that apparently was not tested using a known
      approach" [Zalewski2002].

   June 2007:
      OpenBSD implements TCP ISN randomization based on the algorithm
      specified in [RFC1948] (currently obsoleted and replaced by
      [RFC6528]) for the TCP endpoint that performs the active open
      while keeping the simple randomization scheme for the endpoint
      performing the passive open [OpenBSD-TCP-ISN-H].  This provides
      monotonically increasing ISNs for the "client side" (allowing the
      BSD heuristics to work as expected) while avoiding any patterns in
      the ISN generation for the "server side".

   February 2012:
      [RFC6528], published 27 years after Morris's original work
      [Morris1985], formally updates [RFC0793] to mitigate predictable
      TCP ISNs.

   August 2014:
      The algorithm specified in [RFC6528] becomes the recommended
      ("SHOULD") algorithm for TCP ISN generation in
      [draft-eddy-rfc793bis-04], an early revision of the core TCP
      specification [RFC9293].

   August 2022:
      [RFC9293], a revision of the core TCP specification, is published,
      adopting the algorithm specified in [RFC6528] as the recommended
      ("SHOULD") algorithm for TCP ISN generation.

4.3.  IPv6 Interface Identifiers (IIDs)

   IPv6 Interface Identifiers can be generated as a result of different
   mechanisms, including Stateless Address Autoconfiguration (SLAAC)
   [RFC4862], DHCPv6 [RFC8415], and manual configuration.  This section
   focuses on Interface Identifiers resulting from SLAAC.

   The Interface Identifier of stable IPv6 addresses resulting from
   SLAAC originally resulted in the underlying link-layer address being
   embedded in the IID.  At the time, employing the underlying link-
   layer address for the IID was seen as a convenient way to obtain a
   unique address.  However, recent awareness about the security and
   privacy properties of this approach [RFC7707] [RFC7721] has led to
   the replacement of this flawed scheme with an alternative one
   [RFC7217] [RFC8064] that does not negatively affect the security and
   privacy properties of the protocol.

   January 1997:
      [RFC2073] specifies the syntax of IPv6 global addresses (referred
      to as "An IPv6 Provider-Based Unicast Address Format" at the
      time), which is consistent with the IPv6 addressing architecture
      specified in [RFC1884].  Hosts are recommended to "generate
      addresses using link-specific addresses as Interface ID such as 48
      bit IEEE-802 MAC addresses".

   July 1998:
      [RFC2374] specifies "An IPv6 Aggregatable Global Unicast Address
      Format" (obsoleting [RFC2073]), changing the size of the IID to 64
      bits, and specifies that IIDs must be constructed in IEEE 64-bit
      Extended Unique Identifier (EUI-64) format.  How such identifiers
      are constructed is specified in the corresponding "IPv6 over
      <link>" specifications, such as "IPv6 over Ethernet".

   January 2001:
      [RFC3041] recognizes the problem of IPv6 network activity
      correlation and specifies IPv6 temporary addresses.  Temporary
      addresses are to be used along with stable addresses.

   August 2003:
      [RFC3587] obsoletes [RFC2374], making the Top-Level Aggregator
      (TLA) / Next-Level Aggregator (NLA) structure historic, though the
      syntax and recommendations for the stable IIDs remain unchanged.

   February 2006:
      [RFC4291] is published as the latest "IP Version 6 Addressing
      Architecture", requiring the IIDs of "all unicast addresses,
      except those that start with the binary value 000" to employ the
      Modified EUI-64 format.  The details of constructing such
      interface identifiers are defined in the corresponding "IPv6 over
      <link>" specifications.

   March 2008:
      [RFC5157] provides hints regarding how patterns in IPv6 addresses
      could be leveraged for the purpose of address scanning.

   December 2011:
      [draft-gont-6man-stable-privacy-addresses-00] notes that the
      original scheme for generating stable addresses allows for IPv6
      address scanning and for active host tracking (even when IPv6
      temporary addresses are employed).  It also specifies an
      alternative algorithm meant to replace IIDs based on Modified
      EUI-64 format identifiers.

   November 2012:
      The 6man WG adopts [draft-gont-6man-stable-privacy-addresses-01]
      as a working group item (as
      [draft-ietf-6man-stable-privacy-addresses-00]).  However, the
      document no longer formally updates [RFC4291]; therefore, the
      specified algorithm no longer formally replaces the Modified
      EUI-64 format identifiers.

   February 2013:
      An address-scanning tool (scan6 of [IPv6-Toolkit]) that leverages
      IPv6 address patterns is released [Gont2013].

   July 2013:
      [draft-cooper-6man-ipv6-address-generation-privacy-00] elaborates
      on the security and privacy properties of all known algorithms for
      generating IPv6 IIDs.

   January 2014:
      The 6man WG posts [draft-ietf-6man-default-iids-00]
      ("Recommendation on Stable IPv6 Interface Identifiers"),
      recommending [draft-ietf-6man-stable-privacy-addresses-17] for the
      generation of stable addresses.

   April 2014:
      [RFC7217] (formerly [draft-ietf-6man-stable-privacy-addresses-17])
      is published, specifying "A Method for Generating Semantically
      Opaque Interface Identifiers with IPv6 Stateless Address
      Autoconfiguration (SLAAC)" as an alternative to (but *not*
      replacement of) Modified EUI-64 format IIDs.

   March 2016:
      [RFC7707] (formerly [draft-gont-opsec-ipv6-host-scanning-02] and
      later [draft-ietf-opsec-ipv6-host-scanning-08]), about "Network
      Reconnaissance in IPv6 Networks", is published.

   March 2016:
      [RFC7721] (formerly
      [draft-cooper-6man-ipv6-address-generation-privacy-00] and later
      [draft-ietf-6man-ipv6-address-generation-privacy-08]), about
      "Security and Privacy Considerations for IPv6 Address Generation
      Mechanisms", is published.

   May 2016:
      [draft-gont-6man-non-stable-iids-00] is posted, with the goal of
      specifying requirements for non-stable addresses and updating
      [RFC4941] such that use of only temporary addresses is allowed.

   May 2016:
      [draft-gont-6man-address-usage-recommendations-00] is posted,
      providing an analysis of how different aspects on an address (from
      stability to usage mode) affect their corresponding security and
      privacy properties and meaning to eventually provide advice in
      this area.

   February 2017:
      [draft-ietf-6man-default-iids-16], produced by the 6man WG, is
      published as [RFC8064] ("Recommendation on Stable IPv6 Interface
      Identifiers"), with requirements for stable addresses and a
      recommendation to employ [RFC7217] for the generation of stable
      addresses.  It formally updates a large number of RFCs.

   March 2018:
      [draft-fgont-6man-rfc4941bis-00] is posted (as suggested by the
      6man WG) to address flaws in [RFC4941] by revising it (as an
      alternative to the [draft-gont-6man-non-stable-iids-00] effort,
      posted in March 2016).

   July 2018:
      [draft-fgont-6man-rfc4941bis-00] is adopted (as
      [draft-ietf-6man-rfc4941bis-00]) as a WG item of the 6man WG.

   December 2020:
      [draft-ietf-6man-rfc4941bis-12] is approved by the IESG for
      publication as an RFC.

   February 2021:
      [draft-ietf-6man-rfc4941bis-12] is finally published as [RFC8981].

4.4.  NTP Reference IDs (REFIDs)

   The NTP [RFC5905] Reference ID is a 32-bit code identifying the
   particular server or reference clock.  Above stratum 1 (secondary
   servers and clients), this value can be employed to avoid degree-one
   timing loops, that is, scenarios where two NTP peers are (mutually)
   the time source of each other.  If using the IPv4 address family, the
   identifier is the four-octet IPv4 address.  If using the IPv6 address
   family, it is the first four octets of the MD5 hash of the IPv6
   address.

   June 2010:
      [RFC5905] ("Network Time Protocol Version 4: Protocol and
      Algorithms Specification") is published.  It specifies that, for
      NTP peers with stratum higher than 1, the REFID embeds the IPv4
      address of the time source or the first four octets of the MD5
      hash of the IPv6 address of the time source.

   July 2016:
      [draft-stenn-ntp-not-you-refid-00] is posted, describing the
      information leakage produced via the NTP REFID.  It proposes that
      NTP returns a special REFID when a packet employs an IP Source
      Address that is not believed to be a current NTP peer but
      otherwise generates and returns the common REFID.  It is
      subsequently adopted by the NTP WG as
      [draft-ietf-ntp-refid-updates-00].

   April 2019:
      [Gont-NTP] notes that the proposed fix specified in
      [draft-ietf-ntp-refid-updates-00] is, at the very least, sub-
      optimal.  As a result of a lack of WG support, the
      [draft-ietf-ntp-refid-updates-00] effort is eventually abandoned.

4.5.  Transport-Protocol Ephemeral Port Numbers

   Most (if not all) transport protocols employ "port numbers" to
   demultiplex packets to the corresponding transport-protocol
   instances.  "Ephemeral ports" refer to the local ports employed in
   active OPEN requests, that is, typically the local port numbers
   employed on the side initiating the communication.

   August 1980:
      [RFC0768] notes that the UDP source port is optional and
      identifies the port of the sending process.  It does not specify
      interoperability requirements for source port selection, nor does
      it suggest possible ways to select port numbers.  Most popular
      implementations end up selecting source ports from a system-wide
      global counter.

   September 1981:
      [RFC0793] (the TCP specification) essentially describes the use of
      port numbers and specifies that port numbers should result in a
      unique socket pair {local address, local port, remote address,
      remote port}. How ephemeral ports are selected and the port range
      from which they are selected are left unspecified.

   July 1996:
      OpenBSD implements ephemeral port randomization [OpenBSD-PR].

   July 2008:
      The CERT Coordination Center publishes details of what became
      known as the "Kaminsky Attack" [VU-800113] [Kaminsky2008] on the
      DNS.  The attack exploits the lack of ephemeral port randomization
      and DNS ID randomization in many major DNS implementations to
      perform cache poisoning in an effective and practical manner.

   January 2009:
      [RFC5452] mandates the use of port randomization for DNS resolvers
      and mandates that implementations must randomize ports from the
      range of available ports (53 or 1024 and above) that is as large
      as possible and practicable.  It does not recommend possible
      algorithms for port randomization, although the document
      specifically targets DNS resolvers, for which a simple port
      randomization suffices (e.g., Algorithm 1 of [RFC6056]).  This
      document led to the implementation of port randomization in the
      DNS resolvers themselves, rather than in the underlying transport
      protocols.

   January 2011:
      [RFC6056] notes that many TCP and UDP implementations result in
      predictable ephemeral port numbers and also notes that many
      implementations select port numbers from a small portion of the
      whole port number space.  It recommends the implementation and use
      of ephemeral port randomization, proposes a number of possible
      algorithms for port randomization, and also recommends to
      randomize port numbers over the range 1024-65535.

   March 2016:
      [NIST-NTP] reports a non-normal distribution of the ephemeral port
      numbers employed by the NTP clients of an Internet Time Service.

   April 2019:
      [draft-gont-ntp-port-randomization-00] notes that some NTP
      implementations employ the NTP service port (123) as the local
      port for nonsymmetric modes and aims to update the NTP
      specification to recommend port randomization in such cases, which
      is in line with [RFC6056].  The proposal experiences some pushback
      in the relevant working group (NTP WG) [NTP-PORTR] but is finally
      adopted as a working group item as
      [draft-ietf-ntp-port-randomization-00].

   August 2021:
      [draft-ietf-ntp-port-randomization-08] is finally published as
      [RFC9109].

4.6.  DNS ID

   The DNS ID [RFC1035] can be employed to match DNS replies to
   outstanding DNS queries.

      |  NOTE: Some documents refer to the DNS ID as the DNS "Query ID"
      |  or "TxID".

   November 1987:
      [RFC1035] specifies that the DNS ID is a 16-bit identifier
      assigned by the program that generates any kind of query and that
      this identifier is copied in the corresponding reply and can be
      used by the requester to match up replies to outstanding queries.
      It does not specify the interoperability requirements for this
      numeric identifier, nor does it suggest an algorithm for
      generating it.

   August 1993:
      [Schuba1993] describes DNS cache poisoning attacks that require
      the attacker to guess the DNS ID.

   June 1995:
      [Vixie1995] suggests that both the UDP source port and the DNS ID
      of query packets should be randomized, although that might not
      provide enough entropy to prevent an attacker from guessing these
      values.

   April 1997:
      [Arce1997] finds that implementations employ predictable UDP
      source ports and predictable DNS IDs and argues that both should
      be randomized.

   November 2002:
      [Sacramento2002] finds that, by spoofing multiple requests for the
      same domain name from different IP addresses, an attacker may
      guess the DNS ID employed for a victim with a high probability of
      success, thus allowing for DNS cache poisoning attacks.

   March 2007:
      [Klein2007c] finds that the Microsoft Windows DNS server generates
      predictable DNS ID values.

   July 2007:
      [Klein2007b] finds that a popular DNS server software (BIND 9)
      that randomizes the DNS ID is still subject to DNS cache poisoning
      attacks by forging a large number of queries and leveraging the
      birthday paradox.

   October 2007:
      [Klein2007] finds that OpenBSD's DNS software (based on the BIND
      DNS server of the Internet Systems Consortium (ISC)) generates
      predictable DNS ID values.

   January 2009:
      [RFC5452] is published, requiring resolvers to randomize the DNS
      ID of queries and to verify that the DNS ID of a reply matches
      that of the DNS query as part of the DNS reply validation process.

   May 2010:
      [Economou2010] finds that the Windows SMTP Service implements its
      own DNS resolver that results in predictable DNS ID values.
      Additionally, it fails to validate that the DNS ID of a reply
      matches that of the DNS query that supposedly elicited it.

5.  Conclusions

   For more than 30 years, a large number of implementations of IETF
   protocols have been subject to a variety of attacks, with effects
   ranging from Denial of Service (DoS) or data injection to information
   leakages that could be exploited for pervasive monitoring [RFC7258].
   The root cause of these issues has been, in many cases, the poor
   selection of transient numeric identifiers in such protocols, usually
   as a result of insufficient or misleading specifications.

   While it is generally possible to identify an algorithm that can
   satisfy the interoperability requirements for a given transient
   numeric identifier, this document provides empirical evidence that
   doing so without negatively affecting the security and/or privacy
   properties of the aforementioned protocols is nontrivial.  It is thus
   evident that advice in this area is warranted.

   [RFC9416] aims at requiring future IETF protocol specifications to
   contain analysis of the security and privacy properties of any
   transient numeric identifiers specified by the protocol and to
   recommend an algorithm for the generation of such transient numeric
   identifiers.  [RFC9415] specifies a number of sample algorithms for
   generating transient numeric identifiers with specific
   interoperability requirements and failure severities.

6.  IANA Considerations

   This document has no IANA actions.

7.  Security Considerations

   This document analyzes the timeline of the specification and
   implementation of the transient numeric identifiers of some sample
   IETF protocols and how the security and privacy properties of such
   protocols have been affected as a result of it.  It provides concrete
   evidence that advice in this area is warranted.

   [RFC9415] analyzes and categorizes transient numeric identifiers
   based on their interoperability requirements and their associated
   failure severities and recommends possible algorithms that can be
   employed to comply with those requirements without negatively
   affecting the security and privacy properties of the corresponding
   protocols.

   [RFC9416] formally requires IETF protocol specifications to specify
   the interoperability requirements for their transient numeric
   identifiers, to do a warranted vulnerability assessment of such
   transient numeric identifiers, and to recommend possible algorithms
   for their generation, such that the interoperability requirements are
   complied with, while any negative security or privacy properties of
   these transient numeric identifiers are mitigated.

8.  References

8.1.  Normative References

   [RFC0768]  Postel, J., "User Datagram Protocol", STD 6, RFC 768,
              DOI 10.17487/RFC0768, August 1980,
              <https://www.rfc-editor.org/info/rfc768>.

   [RFC0791]  Postel, J., "Internet Protocol", STD 5, RFC 791,
              DOI 10.17487/RFC0791, September 1981,
              <https://www.rfc-editor.org/info/rfc791>.

   [RFC0793]  Postel, J., "Transmission Control Protocol", RFC 793,
              DOI 10.17487/RFC0793, September 1981,
              <https://www.rfc-editor.org/info/rfc793>.

   [RFC1323]  Jacobson, V., Braden, R., and D. Borman, "TCP Extensions
              for High Performance", RFC 1323, DOI 10.17487/RFC1323, May
              1992, <https://www.rfc-editor.org/info/rfc1323>.

   [RFC1883]  Deering, S. and R. Hinden, "Internet Protocol, Version 6
              (IPv6) Specification", RFC 1883, DOI 10.17487/RFC1883,
              December 1995, <https://www.rfc-editor.org/info/rfc1883>.

   [RFC1884]  Hinden, R., Ed. and S. Deering, Ed., "IP Version 6
              Addressing Architecture", RFC 1884, DOI 10.17487/RFC1884,
              December 1995, <https://www.rfc-editor.org/info/rfc1884>.

   [RFC2073]  Rekhter, Y., Lothberg, P., Hinden, R., Deering, S., and J.
              Postel, "An IPv6 Provider-Based Unicast Address Format",
              RFC 2073, DOI 10.17487/RFC2073, January 1997,
              <https://www.rfc-editor.org/info/rfc2073>.

   [RFC2374]  Hinden, R., O'Dell, M., and S. Deering, "An IPv6
              Aggregatable Global Unicast Address Format", RFC 2374,
              DOI 10.17487/RFC2374, July 1998,
              <https://www.rfc-editor.org/info/rfc2374>.

   [RFC2460]  Deering, S. and R. Hinden, "Internet Protocol, Version 6
              (IPv6) Specification", RFC 2460, DOI 10.17487/RFC2460,
              December 1998, <https://www.rfc-editor.org/info/rfc2460>.

   [RFC3041]  Narten, T. and R. Draves, "Privacy Extensions for
              Stateless Address Autoconfiguration in IPv6", RFC 3041,
              DOI 10.17487/RFC3041, January 2001,
              <https://www.rfc-editor.org/info/rfc3041>.

   [RFC3587]  Hinden, R., Deering, S., and E. Nordmark, "IPv6 Global
              Unicast Address Format", RFC 3587, DOI 10.17487/RFC3587,
              August 2003, <https://www.rfc-editor.org/info/rfc3587>.

   [RFC4291]  Hinden, R. and S. Deering, "IP Version 6 Addressing
              Architecture", RFC 4291, DOI 10.17487/RFC4291, February
              2006, <https://www.rfc-editor.org/info/rfc4291>.

   [RFC4862]  Thomson, S., Narten, T., and T. Jinmei, "IPv6 Stateless
              Address Autoconfiguration", RFC 4862,
              DOI 10.17487/RFC4862, September 2007,
              <https://www.rfc-editor.org/info/rfc4862>.

   [RFC4941]  Narten, T., Draves, R., and S. Krishnan, "Privacy
              Extensions for Stateless Address Autoconfiguration in
              IPv6", RFC 4941, DOI 10.17487/RFC4941, September 2007,
              <https://www.rfc-editor.org/info/rfc4941>.

   [RFC5452]  Hubert, A. and R. van Mook, "Measures for Making DNS More
              Resilient against Forged Answers", RFC 5452,
              DOI 10.17487/RFC5452, January 2009,
              <https://www.rfc-editor.org/info/rfc5452>.

   [RFC6056]  Larsen, M. and F. Gont, "Recommendations for Transport-
              Protocol Port Randomization", BCP 156, RFC 6056,
              DOI 10.17487/RFC6056, January 2011,
              <https://www.rfc-editor.org/info/rfc6056>.

   [RFC6528]  Gont, F. and S. Bellovin, "Defending against Sequence
              Number Attacks", RFC 6528, DOI 10.17487/RFC6528, February
              2012, <https://www.rfc-editor.org/info/rfc6528>.

   [RFC7217]  Gont, F., "A Method for Generating Semantically Opaque
              Interface Identifiers with IPv6 Stateless Address
              Autoconfiguration (SLAAC)", RFC 7217,
              DOI 10.17487/RFC7217, April 2014,
              <https://www.rfc-editor.org/info/rfc7217>.

   [RFC7323]  Borman, D., Braden, B., Jacobson, V., and R.
              Scheffenegger, Ed., "TCP Extensions for High Performance",
              RFC 7323, DOI 10.17487/RFC7323, September 2014,
              <https://www.rfc-editor.org/info/rfc7323>.

   [RFC8200]  Deering, S. and R. Hinden, "Internet Protocol, Version 6
              (IPv6) Specification", STD 86, RFC 8200,
              DOI 10.17487/RFC8200, July 2017,
              <https://www.rfc-editor.org/info/rfc8200>.

   [RFC8415]  Mrugalski, T., Siodelski, M., Volz, B., Yourtchenko, A.,
              Richardson, M., Jiang, S., Lemon, T., and T. Winters,
              "Dynamic Host Configuration Protocol for IPv6 (DHCPv6)",
              RFC 8415, DOI 10.17487/RFC8415, November 2018,
              <https://www.rfc-editor.org/info/rfc8415>.

   [RFC9293]  Eddy, W., Ed., "Transmission Control Protocol (TCP)",
              STD 7, RFC 9293, DOI 10.17487/RFC9293, August 2022,
              <https://www.rfc-editor.org/info/rfc9293>.

8.2.  Informative References

   [Arce1997] Arce, I. and E. Kargieman, "BIND Vulnerabilities and
              Solutions", April 1997,
              <http://www.openbsd.org/advisories/sni_12_resolverid.txt>.

   [Bellovin1989]
              Bellovin, S., "Security Problems in the TCP/IP Protocol
              Suite", Computer Communications Review, vol. 19, no. 2,
              pp. 32-48, April 1989,
              <https://www.cs.columbia.edu/~smb/papers/ipext.pdf>.

   [Bellovin2002]
              Bellovin, S., "A Technique for Counting NATted Hosts",
              IMW'02, Marseille, France, DOI 10.1145/637201.637243,
              November 2002,
              <https://www.cs.columbia.edu/~smb/papers/fnat.pdf>.

   [CERT2001] CERT/CC, "CERT Advisory CA-2001-09: Statistical Weaknesses
              in TCP/IP Initial Sequence Numbers", May 2001,
              <https://resources.sei.cmu.edu/asset_files/
              WhitePaper/2001_019_001_496192.pdf>.

   [draft-cooper-6man-ipv6-address-generation-privacy-00]
              Cooper, A., Gont, F., and D. Thaler, "Privacy
              Considerations for IPv6 Address Generation Mechanisms",
              Work in Progress, Internet-Draft, draft-cooper-6man-ipv6-
              address-generation-privacy-00, 15 July 2013,
              <https://www.ietf.org/archive/id/draft-cooper-6man-ipv6-
              address-generation-privacy-00.txt>.

   [draft-eddy-rfc793bis-04]
              Eddy, W., Ed., "Transmission Control Protocol
              Specification", Work in Progress, Internet-Draft, draft-
              eddy-rfc793bis-04, 25 August 2014,
              <https://www.ietf.org/archive/id/draft-eddy-rfc793bis-
              04.txt>.

   [draft-fgont-6man-rfc4941bis-00]
              Gont, F., Krishnan, S., Narten, T., and R. Draves,
              "Privacy Extensions for Stateless Address
              Autoconfiguration in IPv6", Work in Progress, Internet-
              Draft, draft-fgont-6man-rfc4941bis-00, 25 March 2018,
              <https://www.ietf.org/archive/id/draft-fgont-6man-
              rfc4941bis-00.txt>.

   [draft-gont-6man-address-usage-recommendations-00]
              Gont, F. and W. LIU, "IPv6 Address Usage Recommendations",
              Work in Progress, Internet-Draft, draft-gont-6man-address-
              usage-recommendations-00, 27 May 2016,
              <https://www.ietf.org/archive/id/draft-gont-6man-address-
              usage-recommendations-00.txt>.

   [draft-gont-6man-non-stable-iids-00]
              Gont, F. and W. Liu, "Recommendation on Non-Stable IPv6
              Interface Identifiers", Work in Progress, Internet-Draft,
              draft-gont-6man-non-stable-iids-00, 23 May 2016,
              <https://www.ietf.org/archive/id/draft-gont-6man-non-
              stable-iids-00.txt>.

   [draft-gont-6man-predictable-fragment-id-00]
              Gont, F., "Security Implications of Predictable Fragment
              Identification Values", Work in Progress, Internet-Draft,
              draft-gont-6man-predictable-fragment-id-00, 15 December
              2011, <https://www.ietf.org/archive/id/draft-gont-6man-
              predictable-fragment-id-00.txt>.

   [draft-gont-6man-predictable-fragment-id-03]
              Gont, F., "Security Implications of Predictable Fragment
              Identification Values", Work in Progress, Internet-Draft,
              draft-gont-6man-predictable-fragment-id-03, 9 January
              2013, <https://www.ietf.org/archive/id/draft-gont-6man-
              predictable-fragment-id-03.txt>.

   [draft-gont-6man-stable-privacy-addresses-00]
              Gont, F., "A method for Generating Stable Privacy-Enhanced
              Addresses with IPv6 Stateless Address Autoconfiguration
              (SLAAC)", Work in Progress, Internet-Draft, draft-gont-
              6man-stable-privacy-addresses-00, 15 December 2011,
              <https://www.ietf.org/archive/id/draft-gont-6man-stable-
              privacy-addresses-00.txt>.

   [draft-gont-6man-stable-privacy-addresses-01]
              Gont, F., "A method for Generating Stable Privacy-Enhanced
              Addresses with IPv6 Stateless Address Autoconfiguration
              (SLAAC)", Work in Progress, Internet-Draft, draft-gont-
              6man-stable-privacy-addresses-01, 31 March 2012,
              <https://www.ietf.org/archive/id/draft-gont-6man-stable-
              privacy-addresses-01.txt>.

   [draft-gont-ntp-port-randomization-00]
              Gont, F. and G. Gont, "Port Randomization in the Network
              Time Protocol Version 4", Work in Progress, Internet-
              Draft, draft-gont-ntp-port-randomization-00, 16 April
              2019, <https://www.ietf.org/archive/id/draft-gont-ntp-
              port-randomization-00.txt>.

   [draft-gont-opsec-ipv6-host-scanning-02]
              Gont, F. and T. Chown, "Network Reconnaissance in IPv6
              Networks", Work in Progress, Internet-Draft, draft-gont-
              opsec-ipv6-host-scanning-02, 23 October 2012,
              <https://www.ietf.org/archive/id/draft-gont-opsec-ipv6-
              host-scanning-02.txt>.

   [draft-gont-predictable-numeric-ids-03]
              Gont, F. and I. Arce, "Security and Privacy Implications
              of Numeric Identifiers Employed in Network Protocols",
              Work in Progress, Internet-Draft, draft-gont-predictable-
              numeric-ids-03, 11 March 2019,
              <https://datatracker.ietf.org/doc/html/draft-gont-
              predictable-numeric-ids-03>.

   [draft-ietf-6man-default-iids-00]
              Gont, F., Cooper, A., Thaler, D., and W. Liu,
              "Recommendation on Stable IPv6 Interface Identifiers",
              Work in Progress, Internet-Draft, draft-ietf-6man-default-
              iids-00, 24 January 2014,
              <https://www.ietf.org/archive/id/draft-ietf-6man-default-
              iids-00.txt>.

   [draft-ietf-6man-default-iids-16]
              Gont, F., Cooper, A., Thaler, D., and W. LIU,
              "Recommendation on Stable IPv6 Interface Identifiers",
              Work in Progress, Internet-Draft, draft-ietf-6man-default-
              iids-16, 28 September 2016,
              <https://www.ietf.org/archive/id/draft-ietf-6man-default-
              iids-16.txt>.

   [draft-ietf-6man-ipv6-address-generation-privacy-08]
              Cooper, A., Gont, F., and D. Thaler, "Privacy
              Considerations for IPv6 Address Generation Mechanisms",
              Work in Progress, Internet-Draft, draft-ietf-6man-ipv6-
              address-generation-privacy-08, 23 September 2015,
              <https://www.ietf.org/archive/id/draft-ietf-6man-ipv6-
              address-generation-privacy-08.txt>.

   [draft-ietf-6man-predictable-fragment-id-00]
              Gont, F., "Security Implications of Predictable Fragment
              Identification Values", Work in Progress, Internet-Draft,
              draft-ietf-6man-predictable-fragment-id-00, 22 March 2013,
              <https://www.ietf.org/archive/id/draft-ietf-6man-
              predictable-fragment-id-00.txt>.

   [draft-ietf-6man-predictable-fragment-id-01]
              Gont, F., "Security Implications of Predictable Fragment
              Identification Values", Work in Progress, Internet-Draft,
              draft-ietf-6man-predictable-fragment-id-01, 29 April 2014,
              <https://www.ietf.org/archive/id/draft-ietf-6man-
              predictable-fragment-id-01.txt>.

   [draft-ietf-6man-predictable-fragment-id-02]
              Gont, F., "Security Implications of Predictable Fragment
              Identification Values", Work in Progress, Internet-Draft,
              draft-ietf-6man-predictable-fragment-id-02, 19 December
              2014, <https://datatracker.ietf.org/doc/html/draft-ietf-
              6man-predictable-fragment-id-02>.

   [draft-ietf-6man-predictable-fragment-id-08]
              Gont, F., "Security Implications of Predictable Fragment
              Identification Values", Work in Progress, Internet-Draft,
              draft-ietf-6man-predictable-fragment-id-08, 9 June 2015,
              <https://www.ietf.org/archive/id/draft-ietf-6man-
              predictable-fragment-id-08.txt>.

   [draft-ietf-6man-predictable-fragment-id-10]
              Gont, F., "Security Implications of Predictable Fragment
              Identification Values", Work in Progress, Internet-Draft,
              draft-ietf-6man-predictable-fragment-id-10, 9 October
              2015, <https://www.ietf.org/archive/id/draft-ietf-6man-
              predictable-fragment-id-10.txt>.

   [draft-ietf-6man-rfc2460bis-05]
              Deering, S. and R. Hinden, "Internet Protocol, Version 6
              (IPv6) Specification", Work in Progress, Internet-Draft,
              draft-ietf-6man-rfc2460bis-05, 28 June 2016,
              <https://www.ietf.org/archive/id/draft-ietf-6man-
              rfc2460bis-05.txt>.

   [draft-ietf-6man-rfc2460bis-13]
              Deering, S. and R. Hinden, "draft-ietf-6man-rfc2460bis-
              13", Work in Progress, Internet-Draft, draft-ietf-6man-
              rfc2460bis-13, 19 May 2017,
              <https://www.ietf.org/archive/id/draft-ietf-6man-
              rfc2460bis-13.txt>.

   [draft-ietf-6man-rfc4941bis-00]
              Gont, F., Krishnan, S., Narten, T., and R. Draves,
              "Privacy Extensions for Stateless Address
              Autoconfiguration in IPv6", Work in Progress, Internet-
              Draft, draft-ietf-6man-rfc4941bis-00, 2 July 2018,
              <https://www.ietf.org/archive/id/draft-ietf-6man-
              rfc4941bis-00.txt>.

   [draft-ietf-6man-rfc4941bis-12]
              Gont, F., Krishnan, S., Narten, T., and R. Draves,
              "Temporary Address Extensions for Stateless Address
              Autoconfiguration in IPv6", Work in Progress, Internet-
              Draft, draft-ietf-6man-rfc4941bis-12, 2 November 2020,
              <https://www.ietf.org/archive/id/draft-ietf-6man-
              rfc4941bis-12.txt>.

   [draft-ietf-6man-stable-privacy-addresses-00]
              Gont, F., "A method for Generating Stable Privacy-Enhanced
              Addresses with IPv6 Stateless Address Autoconfiguration
              (SLAAC)", Work in Progress, Internet-Draft, draft-ietf-
              6man-stable-privacy-addresses-00, 18 May 2012,
              <https://www.ietf.org/archive/id/draft-ietf-6man-stable-
              privacy-addresses-00.txt>.

   [draft-ietf-6man-stable-privacy-addresses-17]
              Gont, F., "A Method for Generating Semantically Opaque
              Interface Identifiers with IPv6 Stateless Address
              Autoconfiguration (SLAAC)", Work in Progress, Internet-
              Draft, draft-ietf-6man-stable-privacy-addresses-17, 27
              January 2014, <https://www.ietf.org/archive/id/draft-ietf-
              6man-stable-privacy-addresses-17.txt>.

   [draft-ietf-ntp-port-randomization-00]
              Gont, F., Gont, G., and M. Lichvar, "Port Randomization in
              the Network Time Protocol Version 4", Work in Progress,
              Internet-Draft, draft-ietf-ntp-port-randomization-00, 22
              October 2019, <https://www.ietf.org/archive/id/draft-ietf-
              ntp-port-randomization-00.txt>.

   [draft-ietf-ntp-port-randomization-08]
              Gont, F., Gont, G., and M. Lichvar, "Port Randomization in
              the Network Time Protocol Version 4", Work in Progress,
              Internet-Draft, draft-ietf-ntp-port-randomization-00, 10
              June 2021, <https://www.ietf.org/archive/id/draft-ietf-
              ntp-port-randomization-08.txt>.

   [draft-ietf-ntp-refid-updates-00]
              Stenn, H. and S. Goldberg, "Network Time Protocol REFID
              Updates", Work in Progress, Internet-Draft, draft-ietf-
              ntp-refid-updates-00, 13 November 2016,
              <https://www.ietf.org/archive/id/draft-ietf-ntp-refid-
              updates-00.txt>.

   [draft-ietf-opsec-ipv6-host-scanning-08]
              Gont, F. and T. Chown, "Network Reconnaissance in IPv6
              Networks", Work in Progress, Internet-Draft, draft-ietf-
              opsec-ipv6-host-scanning-08, 28 August 2015,
              <https://www.ietf.org/archive/id/draft-ietf-opsec-ipv6-
              host-scanning-08.txt>.

   [draft-stenn-ntp-not-you-refid-00]
              Goldberg, S. and H. Stenn, "Network Time Protocol Not You
              REFID", Work in Progress, Internet-Draft, draft-stenn-ntp-
              not-you-refid-00, 8 July 2016,
              <https://www.ietf.org/archive/id/draft-stenn-ntp-not-you-
              refid-00.txt>.

   [Economou2010]
              Economou, N., "Windows SMTP Service DNS query Id
              vulnerabilities", Advisory ID Internal CORE-2010-0427, May
              2010, <https://www.coresecurity.com/core-labs/advisories/
              core-2010-0424-windows-smtp-dns-query-id-bugs>.

   [Fyodor2002]
              Fyodor, "Idle scanning and related IP ID games", September
              2002,
              <https://nmap.org/presentations/CanSecWest03/CD_Content/
              idlescan_paper/idlescan.html>.

   [Gont-NTP] Gont, F., "[Ntp] Comments on draft-ietf-ntp-refid-updates-
              05", message to the IETF NTP mailing list, 16 April 2019,
              <https://mailarchive.ietf.org/arch/msg/ntp/
              NkfTHxUUOdp14Agh3h1IPqfcRRg>.

   [Gont2011] Gont, F., "Hacking IPv6 Networks (training course)", Hack
              In Paris 2011 Conference, Paris, France, June 2011,
              <https://www.si6networks.com/files/presentations/hip2011/
              fgont-hip2011-hacking-ipv6-networks.pdf>.

   [Gont2012] Gont, F., "Recent Advances in IPv6 Security", BSDCan 2012
              Conference, Ottawa, Canada, May 2012,
              <https://www.si6networks.com/files/presentations/
              bsdcan2012/fgont-bsdcan2012-recent-advances-in-
              ipv6-security.pdf>.

   [Gont2013] Gont, F., "Beta release of the SI6 Network's IPv6 Toolkit
              (help wanted!)", message to the IPv6 Hackers mailing list,
              11 February 2013,
              <https://lists.si6networks.com/pipermail/
              ipv6hackers/2013-February/000947.html>.

   [IANA-PROT]
              IANA, "Protocol Registries",
              <https://www.iana.org/protocols>.

   [IPID-DEV] Klein, A. and B. Pinkas, "From IP ID to Device ID and
              KASLR Bypass (Extended Version)",
              DOI 10.48550/arXiv.1906.10478, October 2019,
              <https://arxiv.org/pdf/1906.10478.pdf>.

   [IPv6-Toolkit]
              SI6 Networks, "IPv6 Toolkit",
              <https://www.si6networks.com/tools/ipv6toolkit>.

   [Kaminsky2008]
              Kaminsky, D., "Black Ops 2008: It's The End Of The Cache
              As We Know It", August 2008,
              <https://www.blackhat.com/presentations/bh-jp-08/bh-jp-08-
              Kaminsky/BlackHat-Japan-08-Kaminsky-DNS08-BlackOps.pdf>.

   [Klein2007]
              Klein, A., "OpenBSD DNS Cache Poisoning and Multiple O/S
              Predictable IP ID Vulnerability", October 2007,
              <https://dl.packetstormsecurity.net/papers/attack/OpenBSD_
              DNS_Cache_Poisoning_and_Multiple_OS_Predictable_IP_ID_Vuln
              erability.pdf>.

   [Klein2007b]
              Klein, A., "BIND 9 DNS Cache Poisoning", March 2007,
              <https://citeseerx.ist.psu.edu/doc/10.1.1.86.4474>.

   [Klein2007c]
              Klein, A., "Windows DNS Server Cache Poisoning", March
              2007, <https://dl.packetstormsecurity.net/papers/attack/
              Windows_DNS_Cache_Poisoning.pdf>.

   [Morbitzer2013]
              Morbitzer, M., "[PATCH] TCP Idle Scan in IPv6", message to
              the nmap-dev mailing list, 3 June 2013,
              <https://seclists.org/nmap-dev/2013/q2/394>.

   [Morris1985]
              Morris, R., "A Weakness in the 4.2BSD UNIX TCP/IP
              Software", CSTR 117, AT&T Bell Laboratories, Murray Hill,
              NJ, February 1985,
              <https://pdos.csail.mit.edu/~rtm/papers/117.pdf>.

   [NIST-NTP] Sherman, J. and J. Levine, "Usage Analysis of the NIST
              Internet Time Service", Journal of Research of the
              National Institute of Standards and Technology, Volume
              121, March 2016,
              <https://tf.nist.gov/general/pdf/2818.pdf>.

   [NTP-PORTR]
              Gont, F., "[Ntp] New rev of the NTP port randomization I-D
              (Fwd: New Version Notification for draft-gont-ntp-port-
              randomization-01.txt)", message to the IETF NTP mailing
              list, 21 May 2019,
              <https://mailarchive.ietf.org/arch/msg/ntp/
              xSCu5Vhb3zoWcqEjUMmzP8pOdW4/>.

   [OpenBSD-IPv4-ID]
              OpenBSD, "Randomization of the IPv4 Identification field",
              December 1998,
              <https://cvsweb.openbsd.org/src/sys/netinet/
              ip_id.c?rev=1.1>.

   [OpenBSD-IPv6-ID]
              OpenBSD, "Randomization of the IPv6 Identification field",
              October 2003,
              <https://cvsweb.openbsd.org/src/sys/netinet6/
              ip6_id.c?rev=1.1>.

   [OpenBSD-PR]
              OpenBSD, "Implementation of port randomization", July
              1996, <https://cvsweb.openbsd.org/src/sys/netinet/
              in_pcb.c?rev=1.6>.

   [OpenBSD-TCP-ISN-H]
              OpenBSD, "Implementation of RFC1948 for TCP ISN
              randomization", June 2007,
              <https://cvsweb.openbsd.org/src/sys/netinet/
              tcp_subr.c?rev=1.97>.

   [OpenBSD-TCP-ISN-I]
              OpenBSD, "Implementation of TCP ISN randomization based on
              random increments", July 1996,
              <https://cvsweb.openbsd.org/src/sys/netinet/
              tcp_subr.c?rev=1.6>.

   [OpenBSD-TCP-ISN-R]
              OpenBSD, "Implementation of TCP ISN randomization based on
              simple randomization", December 2000,
              <https://cvsweb.openbsd.org/src/sys/netinet/
              tcp_subr.c?rev=1.37>.

   [RedHat2011]
              Red Hat, "RHSA-2011:1465-1 - Security Advisory", November
              2011, <https://rhn.redhat.com/errata/RHSA-2011-1465.html>.

   [RFC1035]  Mockapetris, P., "Domain names - implementation and
              specification", STD 13, RFC 1035, DOI 10.17487/RFC1035,
              November 1987, <https://www.rfc-editor.org/info/rfc1035>.

   [RFC1948]  Bellovin, S., "Defending Against Sequence Number Attacks",
              RFC 1948, DOI 10.17487/RFC1948, May 1996,
              <https://www.rfc-editor.org/info/rfc1948>.

   [RFC5157]  Chown, T., "IPv6 Implications for Network Scanning",
              RFC 5157, DOI 10.17487/RFC5157, March 2008,
              <https://www.rfc-editor.org/info/rfc5157>.

   [RFC5905]  Mills, D., Martin, J., Ed., Burbank, J., and W. Kasch,
              "Network Time Protocol Version 4: Protocol and Algorithms
              Specification", RFC 5905, DOI 10.17487/RFC5905, June 2010,
              <https://www.rfc-editor.org/info/rfc5905>.

   [RFC6274]  Gont, F., "Security Assessment of the Internet Protocol
              Version 4", RFC 6274, DOI 10.17487/RFC6274, July 2011,
              <https://www.rfc-editor.org/info/rfc6274>.

   [RFC7258]  Farrell, S. and H. Tschofenig, "Pervasive Monitoring Is an
              Attack", BCP 188, RFC 7258, DOI 10.17487/RFC7258, May
              2014, <https://www.rfc-editor.org/info/rfc7258>.

   [RFC7707]  Gont, F. and T. Chown, "Network Reconnaissance in IPv6
              Networks", RFC 7707, DOI 10.17487/RFC7707, March 2016,
              <https://www.rfc-editor.org/info/rfc7707>.

   [RFC7721]  Cooper, A., Gont, F., and D. Thaler, "Security and Privacy
              Considerations for IPv6 Address Generation Mechanisms",
              RFC 7721, DOI 10.17487/RFC7721, March 2016,
              <https://www.rfc-editor.org/info/rfc7721>.

   [RFC7739]  Gont, F., "Security Implications of Predictable Fragment
              Identification Values", RFC 7739, DOI 10.17487/RFC7739,
              February 2016, <https://www.rfc-editor.org/info/rfc7739>.

   [RFC8064]  Gont, F., Cooper, A., Thaler, D., and W. Liu,
              "Recommendation on Stable IPv6 Interface Identifiers",
              RFC 8064, DOI 10.17487/RFC8064, February 2017,
              <https://www.rfc-editor.org/info/rfc8064>.

   [RFC8981]  Gont, F., Krishnan, S., Narten, T., and R. Draves,
              "Temporary Address Extensions for Stateless Address
              Autoconfiguration in IPv6", RFC 8981,
              DOI 10.17487/RFC8981, February 2021,
              <https://www.rfc-editor.org/info/rfc8981>.

   [RFC9109]  Gont, F., Gont, G., and M. Lichvar, "Network Time Protocol
              Version 4: Port Randomization", RFC 9109,
              DOI 10.17487/RFC9109, August 2021,
              <https://www.rfc-editor.org/info/rfc9109>.

   [RFC9415]  Gont, F. and I. Arce, "On the Generation of Transient
              Numeric Identifiers", RFC 9415, DOI 10.17487/RFC9415, July
              2023, <https://www.rfc-editor.org/info/rfc9415>.

   [RFC9416]  Gont, F. and I. Arce, "Security Considerations for
              Transient Numeric Identifiers Employed in Network
              Protocols", BCP 72, RFC 9416, DOI 10.17487/RFC9416, July
              2023, <https://www.rfc-editor.org/info/rfc9416>.

   [Sacramento2002]
              Sacramento, V., "CAIS-ALERT: Vulnerability in the sending
              requests control of BIND", message to the Bugtraq mailing
              list, 25 November 2002,
              <https://seclists.org/bugtraq/2002/Nov/331>.

   [Sanfilippo1998a]
              Sanfilippo, S., "about the ip header id", message to the
              Bugtraq mailing list, 14 December 1998,
              <http://seclists.org/bugtraq/1998/Dec/48>.

   [Sanfilippo1998b]
              Sanfilippo, S., "new tcp scan method", message to the
              Bugtraq mailing list, 18 December 1998,
              <https://seclists.org/bugtraq/1998/Dec/79>.

   [Sanfilippo1999]
              Sanfilippo, S., "more ip id", message to the Bugtraq
              mailing list, November 1999,
              <https://github.com/antirez/hping/raw/master/docs/MORE-
              FUN-WITH-IPID>.

   [Schuba1993]
              Schuba, C., "Addressing Weakness in the Domain Name System
              Protocol", August 1993,
              <http://ftp.cerias.purdue.edu/pub/papers/christoph-schuba/
              schuba-DNS-msthesis.pdf>.

   [Shimomura1995]
              Shimomura, T., "Technical details of the attack described
              by Markoff in NYT", message to the USENET
              comp.security.misc newsgroup, 25 January 1995,
              <https://www.gont.com.ar/files/post-shimomura-usenet.txt>.

   [Silbersack2005]
              Silbersack, M., "Improving TCP/IP security through
              randomization without sacrificing interoperability",
              EuroBSDCon 2005 Conference, January 2005,
              <https://citeseerx.ist.psu.edu/viewdoc/
              download?doi=10.1.1.91.4542&rep=rep1&type=pdf>.

   [SUSE2011] Meissner, M., "[security-announce] SUSE Security
              Announcement: Linux kernel security update (SUSE-
              SA:2011:046)", message to the openSUSE Security Announce
              mailing list, 13 December 2011,
              <https://lists.opensuse.org/opensuse-security-
              announce/2011-12/msg00011.html>.

   [TCPT-uptime]
              McDanel, B., "TCP Timestamping - Obtaining System Uptime
              Remotely", message to the Bugtraq mailing list, March
              2001, <https://seclists.org/bugtraq/2001/Mar/182>.

   [Ubuntu2011]
              Ubuntu, "USN-1253-1: Linux kernel vulnerabilities",
              November 2011,
              <https://ubuntu.com/security/notices/USN-1253-1>.

   [USCERT2001]
              CERT CC, "Multiple TCP/IP implementations may use
              statistically predictable initial sequence numbers",
              Vulnerability Note VU#498440, March 2001,
              <https://www.kb.cert.org/vuls/id/498440>.

   [Vixie1995]
              Vixie, P., "DNS and BIND Security Issues", 5th Usenix
              Security Symposium, June 1995, <https://www.usenix.org/leg
              acy/publications/library/proceedings/security95/
              full_papers/vixie.pdf>.

   [VU-800113]
              CERT/CC, "Multiple DNS implementations vulnerable to cache
              poisoning", Vulnerability Note VU#800113, July 2008,
              <https://www.kb.cert.org/vuls/id/800113>.

   [Wright1994]
              Wright, G. and W. Stevens, "TCP/IP Illustrated, Volume 2:
              The Implementation", Addison-Wesley, February 1995.

   [Zalewski2001]
              Zalewski, M., "Strange Attractors and TCP/IP Sequence
              Number Analysis (2001)", March 2001,
              <https://lcamtuf.coredump.cx/oldtcp/tcpseq.html>.

   [Zalewski2002]
              Zalewski, M., "Strange Attractors and TCP/IP Sequence
              Number Analysis - One Year Later (2002)", 2002,
              <https://lcamtuf.coredump.cx/newtcp/>.

   [Zalewski2003]
              Zalewski, M., "A new TCP/IP blind data injection
              technique?", December 2003,
              <https://lcamtuf.coredump.cx/ipfrag.txt>.

Acknowledgements

   The authors would like to thank (in alphabetical order) Bernard
   Aboba, Dave Crocker, Spencer Dawkins, Theo de Raadt, Sara Dickinson,
   Guillermo Gont, Christian Huitema, Colin Perkins, Vincent Roca, Kris
   Shrishak, Joe Touch, Brian Trammell, and Christopher Wood for
   providing valuable comments on earlier versions of this document.

   The authors would like to thank (in alphabetical order) Steven
   Bellovin, Joseph Lorenzo Hall, Gre Norcie, and Martin Thomson for
   providing valuable comments on
   [draft-gont-predictable-numeric-ids-03], on which this document is
   based.

   Section 4.2 of this document borrows text from [RFC6528], authored by
   Fernando Gont and Steven Bellovin.

   The authors would like to thank Sara Dickinson and Christopher Wood
   for their guidance during the publication process of this document.

   The authors would like to thank Diego Armando Maradona for his magic
   and inspiration.

Authors' Addresses

   Fernando Gont
   SI6 Networks
   Segurola y Habana
   4310 7mo piso
   Ciudad Autonoma de Buenos Aires
   Argentina
   Email: fgont@si6networks.com
   URI:   https://www.si6networks.com


   Ivan Arce
   Quarkslab
   Segurola y Habana
   4310 7mo piso
   Ciudad Autonoma de Buenos Aires
   Argentina
   Email: iarce@quarkslab.com
   URI:   https://www.quarkslab.com

ISO Plain Language

On this page
PROBLEMFor more than 30 years, IETF protocols have used transient numeric identifiers, such as IP Identification values, TCP initial sequence numbers and port numbers, whose predictable choice led to denial of service, data injection and information leakage.
MECHANISMThis document traces a timeline of specification and vulnerability disclosure for a sample of these identifiers and shows that the recurring cause is a specification that under-specifies, over-specifies or is not implemented as written.
WHY IT MATTERSThe analysis is the evidence behind two companion documents: RFC 9415 gives sample generation algorithms and RFC 9416 requires future specifications to state interoperability requirements, assess vulnerabilities and recommend an algorithm.

§1The Same Mistake, Repeated

Networking protocols use a variety of transient numeric identifiers for different protocol objects: IPv4 and IPv6 Identification values, IPv6 Interface Identifiers, transport-protocol ephemeral port numbers, TCP Initial Sequence Numbers, NTP Reference IDs and DNS IDs. These identifiers usually have requirements, such as uniqueness during a specified period, that must be met without negative interoperability consequences and without an associated failure severity when they are not met.

For more than 30 years a large number of implementations of IETF protocols have been subject to attacks with effects ranging from denial of service and data injection to information leakage that could be exploited for pervasive monitoring. The root cause of these issues has in many cases been the poor selection of transient numeric identifiers, usually as a result of insufficient or misleading specifications. While it is generally trivial to identify an algorithm that satisfies the interoperability requirements of a given identifier, empirical evidence exists that doing so without harming the security or privacy properties of the protocol is prone to error. Implementations have been subject to issues from predictable IPv4 and IPv6 Identification values, predictable IPv6 interface identifiers, predictable ephemeral port numbers, predictable TCP initial sequence numbers, predictable initial timestamps in the TCP timestamps option, and predictable DNS IDs.

Recent history indicates that when new protocols are standardized or new implementations are produced, the security and privacy properties of the associated identifiers tend to be overlooked, and inappropriate algorithms are either suggested in the specifications or chosen by implementors.

The document contains a non-exhaustive timeline of the specification and vulnerability disclosures for a sample of these identifiers, and it draws three conclusions. Vulnerabilities associated with inappropriate generation of transient numeric identifiers have affected protocol implementations for an extremely long time. Such vulnerabilities, even when addressed for a given protocol version, were later reintroduced in new versions or new implementations of the same protocol. And standardization efforts that discuss and provide advice in this area can have a positive effect on IETF specifications and their corresponding implementations. The document represents the consensus of the Privacy Enhancements and Assessments Research Group.

The pattern repeats. A protocol needs a number that is only unique for a short time, the specification says little or says too much about how to pick it, implementers choose something simple, and someone finds a way to abuse it. Fixing one protocol does not stop the next one from making the same mistake, which is why this RFC ends with a process requirement rather than a patch.

§2What Counts as a Transient Identifier

A transient numeric identifier is a data object in a protocol specification that can be used to definitely distinguish a protocol object, such as a datagram, network interface, transport-protocol endpoint or session, from all other objects of the same type in a given context. These identifiers are usually defined as a series of bits and represented using integer values, and are typically dynamically selected, as opposed to statically assigned numeric identifiers. Different identifiers may have additional requirements depending on their specific use in a protocol. The document uses the term as a generic name for any data object satisfying that identification property. The terms constant IID, stable IID and temporary IID are to be interpreted as defined in RFC 7721.

The threat model is deliberately narrow. On-path attacks are not considered: the attacker is assumed not to have physical or logical access to the systems being attacked, and can only observe traffic explicitly directed to the attacker. The attacker cannot observe traffic transferred between the sender and the receivers of a target protocol, but may be able to interact with any of these entities, for example by sending traffic to them to sample the transient numeric identifiers those hosts use when talking to the attacker.

Applied to TCP initial sequence numbers, the attacker is unable to capture the traffic of a TCP connection between two other hosts, but is able to establish a TCP connection with any of them to sample the sequence numbers they use. Applied to IPv6 interface identifiers, the attacker may learn a victim's IPv6 address if it becomes exposed, for example when the victim talks to an attacker-operated server, and can then track the host by probing a set of addresses built from target prefixes and the learned interface identifier. None of these scenarios require the attacker to observe traffic not explicitly directed to it.

The document is careful about what the attacker can see. The attacker is off the path: it cannot watch your traffic to a third party, but it can talk to your machine and see what your machine sends. That is enough to learn the pattern of the numbers your machine picks, and that is the whole point of the exercise.

§4Three Ways a Specification Goes Wrong

Most of the problems in this document come from one of three conditions: protocol specifications that under-specify their transient numeric identifiers, specifications that over-specify them, and implementations that fail to comply with the specified requirements.

Under-specification led to implementations vulnerable to numerous off-path attacks. Examples are the specification of TCP local ports in RFC 793 and the specification of the DNS ID in RFC 1035, neither of which said enough about how to choose the value. The TCP local port in an active OPEN request is commonly known as the ephemeral port of the connection.

Over-specification also happened. RFC 4291 essentially overloads the semantics of IPv6 interface identifiers by embedding link-layer addresses in them, when the uniqueness requirement could be met in other ways that do not carry the same security and privacy cost. Similarly, RFC 2460 suggests the use of a global counter for generating IPv6 Identification values, when the requirement of uniqueness per {IPv6 Source Address, IPv6 Destination Address} could be met by other algorithms without the same cost.

Finally, some implementations simply fail to comply. Some popular operating systems still fail to implement transport-protocol ephemeral port randomization, as recommended in RFC 6056, or TCP initial sequence number randomization, as recommended in RFC 9293.

The document closes by pointing at the two companion documents that answer these problems. RFC 9415 analyzes and categorizes transient numeric identifiers by their interoperability requirements and failure severities, and recommends algorithms that meet those requirements without harming security or privacy. RFC 9416 formally requires IETF protocol specifications to state the interoperability requirements for their transient numeric identifiers, to carry out a warranted vulnerability assessment, and to recommend algorithms for generating them so that the requirements are met while negative security or privacy properties are mitigated.

Three failure modes explain the record. Say too little and implementers invent something predictable. Say too much and you lock in a bad method that could have been avoided. Or write a good rule and have implementers ignore it. The two documents that followed from this RFC turn the lesson into a requirement: every new specification must say how the number is chosen, must assess the risk, and must recommend an algorithm.

§4.1The IP Identification Field

The IPv4 Identification field, specified in RFC 791, must be unique for a given {Source Address, Destination Address, Protocol} for as long as the datagram or any fragment of it could be alive in the Internet. The specification suggests that a sending protocol module may keep a table of identifiers, one entry for each destination it has communicated with in the last maximum packet lifetime, and that since the field allows 65,536 different values, hosts may be able to use unique identifiers independent of destination. This has been interpreted many times as a suggestion to use per-destination or global counters. The specification does not suggest any flawed algorithm, but it omits any discussion of the security and privacy implications of predictable values, and many IPv4 implementations ended up generating them with a global counter.

The IPv6 Identification was originally specified in RFC 1883. It serves the same purpose, but sits in the Fragment Header rather than the base header. RFC 1883 states that the Identification must differ from that of any other fragmented packet sent recently with the same source and destination address, and that this can be met with a wrap-around 32-bit counter incremented each time a packet must be fragmented, leaving it an implementation choice whether to use a global or per-destination counter. The suggestion is more explicit than in the IPv4 case. RFC 2460, the first revision of the core IPv6 specification, kept the same text. RFC 8200, the second revision, removes the counter suggestion and points to RFC 7739 for sample algorithms, but still does not introduce security and privacy requirements on the generation of IPv6 Identification values.

The consequences arrived in stages. In December 1998, work showed that predictable IPv4 Identification values, as generated by most popular implementations, can be used to count the packets a target node sends, and that the same weakness supports a port-scanning technique known as idle scan, whose tool was publicly released. In November 1999, the same weakness was shown to reveal the rules of a number of firewalls. In September 2002, the idle scan technique was documented in the popular Network Mapper tool. In November 2002, the Identification field was shown to be exploitable to count the number of systems behind a NAT. In December 2003, a technique for TCP data injection attacks based on predictable IPv4 Identification values was described, requiring less effort than injection with bare TCP packets. In October 2007, a weakness was described in the pseudorandom number generator used by a number of operating systems for IP Identification values, and in June 2011 the idle scan was shown to work against IPv6.

Mitigation took a long time and was repeatedly weakened. OpenBSD implemented randomization of the IPv4 Identification field in December 1998 and of the IPv6 one in October 2003; Linux mitigated predictable IPv6 Identification values in November 2011. A 2011 draft describing the security implications of predictable IPv6 Identification values was intended to update RFC 2460, but in December 2014 the working group changed its intended status to Informational, which meant it no longer formally updated RFC 2460 and the security and privacy requirements on the generation of IPv6 Identification values were eliminated. RFC 7739 in February 2016 analysed the implications and provided guidance for selecting a generation algorithm, but as an Informational RFC it did not formally update RFC 2460 and introduced no requirements. RFC 8200 followed in July 2017. In October 2019 the IPv6 Identification generators of two popular operating systems were reported to be flawed.

The Identification field in an IPv4 packet exists so that fragments of the same packet can be recognised. The original specification mentioned counters, and many systems used one. A counter is guessable, and a guessable Identification lets an attacker count the packets a host sends, scan ports through it, see how many machines sit behind a NAT, or inject data into a connection. Randomising the field fixed it in practice, but the specification was never formally changed to require it.

THE IP IDENTIFICATION FIELD, FROM SPECIFICATION TO GUIDANCE
  1. 1981RFC 791 specifies the IPv4 Identification and does not assess its securityRFC 791
  2. 1995RFC 1883, the first IPv6 specification, suggests a counter for IPv6RFC 1883
  3. 1998Predictable IPv4 Identification values used for packet counting and idle scan
  4. 1998RFC 2460 keeps the counter suggestion for IPv6RFC 2460
  5. 2003TCP data injection based on predictable IPv4 Identification values
  6. 2016RFC 7739 gives guidance on generating IPv6 Identification valuesRFC 7739
  7. 2017RFC 8200 removes the counter suggestion and points to RFC 7739RFC 8200

§4.2TCP Sequence Numbers and IPv6 Interface Identifiers

RFC 793 suggests that the choice of the initial sequence number of a connection is not arbitrary but aims to reduce the chances of a stale segment being accepted by a new incarnation of a previous connection. It suggests a global 32-bit generator incremented by 1 roughly every 4 microseconds. In practice, protection against stale segments is enforced by preventing a new incarnation before twice the maximum segment lifetime has passed since a segment of the old incarnation was last seen, using the TIME-WAIT state and TCP's quiet time. Based on the assumption that initial sequence numbers increase monotonically across connections, many stacks use the sequence number of an incoming SYN to run heuristics that allow a new incarnation while the previous one is still in TIME-WAIT, which avoids an interoperability problem when a node connects to a specific endpoint at a high rate.

A global counter makes the sequence number trivial to predict, which allows a range of attacks. February 1985 saw the first description of exploiting predictable initial sequence numbers to forge TCP connections that could then be leveraged for trust relationship exploitation; April 1989 brought the security considerations for predictable initial sequence numbers. In January 1995 a real-world exploitation of the 1985 attack was reported, ten years after the original work. The first IETF effort to address the problem, RFC 1948 in May 1996, was authored by Steven Bellovin but did not formally update RFC 793. OpenBSD implemented randomization based on random increments in July 1996 and on simple randomization in December 2000. A March 2001 analysis documented statistical weaknesses in some generators, with vulnerability advisories released for popular implementations, and a March 2002 update concluded that many vendors had either ignored the issue or implemented a flawed solution that appeared not to have been tested with a known approach. RFC 6528, published in February 2012 and 27 years after the original work, formally updated RFC 793 to mitigate predictable initial sequence numbers. In August 2014 the RFC 6528 algorithm became the recommended algorithm in a draft revision of the core TCP specification, and RFC 9293, published in August 2022, adopted it.

IPv6 interface identifiers come from several mechanisms, including stateless address autoconfiguration, DHCPv6 and manual configuration. The document focuses on those from stateless address autoconfiguration. The interface identifier of stable IPv6 addresses originally resulted from the underlying link-layer address being embedded in it, which was seen as a convenient way to obtain a unique address. Awareness of the security and privacy cost of that approach led to its replacement with an alternative that does not affect those properties.

The history runs from January 1997, when RFC 2073 recommended generating addresses using link-specific addresses as interface identifiers such as 48-bit IEEE 802 MAC addresses, through July 1998, when RFC 2374 required IIDs in IEEE 64-bit Extended Unique Identifier format, to February 2006, when RFC 4291 required the Modified EUI-64 format for all unicast addresses except those starting with the binary value 000. January 2001 brought RFC 3041, which recognised the problem of IPv6 network activity correlation and specified IPv6 temporary addresses. In March 2008 RFC 5157 gave hints on how patterns in IPv6 addresses could be leveraged for address scanning, and in December 2011 a draft noted that the original scheme allowed IPv6 address scanning and active host tracking even when temporary addresses were employed. That draft stopped short of formally updating RFC 4291, so the specified algorithm never formally replaced Modified EUI-64 identifiers. RFC 7217 in April 2014 specified a method for generating semantically opaque interface identifiers as an alternative to, but not a replacement for, Modified EUI-64 format identifiers. RFC 7707 and RFC 7721 on network reconnaissance in IPv6 and on security and privacy considerations for IPv6 address generation were published in March 2016, and RFC 8064 in February 2017 recommended the RFC 7217 algorithm and formally updated a large number of RFCs. Finally RFC 8981, published in February 2021 after approval in December 2020, addressed the flaws in RFC 4941 by revising it.

TCP's first sequence number had the same problem: a fixed-rate counter makes it predictable, and a predicted sequence number lets an attacker forge a connection. It took 27 years from the first published attack to the specification being updated. IPv6 had a related problem with the address of an interface: embedding the hardware address in it let anyone scan for hosts and follow them across networks, and the fix took a similar long road.

TCP INITIAL SEQUENCE NUMBERS, FROM THE FIRST ATTACK TO THE FIX
  1. 1981RFC 793 suggests a global 32-bit generator incremented every 4 microsecondsRFC 793
  2. 1985Predictable sequence numbers described as a way to forge TCP connections
  3. 1996RFC 1948, the first IETF attempt, does not formally update RFC 793RFC 1948
  4. 2001Statistical weaknesses in sequence number generators reported
  5. 2012RFC 6528 formally updates RFC 793 to mitigate predictable sequence numbersRFC 6528
  6. 2022RFC 9293 adopts the RFC 6528 algorithm as recommendedRFC 9293

§4.6Time Sources, Ports and DNS

NTP Reference IDs. The NTP Reference ID is a 32-bit code identifying the particular server or reference clock. Above stratum 1 it can be used to avoid degree-one timing loops, where two NTP peers are each other's time source. In the IPv4 address family the identifier is the four-octet IPv4 address of the time source; in the IPv6 address family it is the first four octets of the MD5 hash of the IPv6 address. RFC 5905 was published in June 2010. In July 2016 a draft described the information leakage produced through the REFID and proposed that NTP return a special REFID when a packet uses a source address that is not believed to be a current NTP peer. It was adopted by the NTP working group, but in April 2019 the proposal was judged sub-optimal and, for lack of working group support, the effort was abandoned.

Ephemeral port numbers. Most transport protocols use port numbers to demultiplex packets to the right transport instance, and ephemeral ports are the local ports used in active OPEN requests, that is, typically the local ports on the side initiating the communication. RFC 768 notes that the UDP source port is optional and identifies the sending process, but specifies no interoperability requirements for source port selection and suggests no way to select ports; most popular implementations ended up choosing source ports from a system-wide global counter. RFC 793 describes the use of port numbers and requires that they yield a unique socket pair of {local address, local port, remote address, remote port}, but leaves how ephemeral ports are selected, and the range they are chosen from, unspecified. OpenBSD implemented ephemeral port randomization in July 1996.

The consequences were concrete. In July 2008 the CERT Coordination Center published details of what became known as the Kaminsky attack on DNS, exploiting the lack of ephemeral port randomization and DNS ID randomization in many major DNS implementations to poison caches in an effective and practical manner. RFC 5452 in January 2009 mandated port randomization for DNS resolvers, and mandated that implementations randomize ports from the range of available ports, 53 or 1024 and above, as large as possible and practicable, without recommending an algorithm; it led to port randomization in the DNS resolvers themselves rather than in the underlying transport protocols. RFC 6056 in January 2011 noted that many TCP and UDP implementations produce predictable ephemeral port numbers and select them from a small portion of the port number space, recommended implementing ephemeral port randomization, proposed algorithms, and recommended randomizing over the range 1024 to 65535. In March 2016 a report described a non-normal distribution of the ephemeral port numbers used by the NTP clients of an Internet Time Service. A 2019 draft noted that some NTP implementations use the NTP service port 123 as the local port for nonsymmetric modes; it met some pushback in the working group but was eventually adopted and published as RFC 9109 in August 2021.

The DNS ID. The DNS ID, sometimes called the query ID or TxID, matches DNS replies to outstanding queries. RFC 1035, published in November 1987, specified it as a 16-bit identifier assigned by the program that generates a query, copied into the reply, without specifying interoperability requirements or suggesting a generation algorithm. In August 1993 cache poisoning attacks requiring the attacker to guess the DNS ID were described. In June 1995 it was suggested that both the UDP source port and the DNS ID of query packets should be randomised, though with a note that this might not provide enough entropy to prevent guessing. April 1997 work found implementations using predictable UDP source ports and predictable DNS IDs, and argued that both should be randomised. In November 2002 it was shown that spoofing multiple requests for the same domain name from different IP addresses lets an attacker guess the DNS ID with a high probability of success. In March 2007 the Microsoft Windows DNS server was found to generate predictable DNS IDs, and in July 2007 a DNS server that did randomise the ID was still subject to cache poisoning by forging many queries and exploiting the birthday paradox. In October 2007 OpenBSD's DNS software was found to generate predictable IDs. RFC 5452 in January 2009 required resolvers to randomise the DNS ID and to check that a reply's ID matches the query. In May 2010 the Windows SMTP Service was found to run its own resolver with predictable DNS IDs and to fail to validate that a reply's ID matched the query that supposedly elicited it.

Three more identifiers show the same story. The NTP reference ID reveals which clock a server is using, which leaks information about the network. Ephemeral port numbers chosen from a counter let an attacker find and target a machine without seeing any traffic. And the DNS query ID, a 16-bit number copied into the reply, let an attacker poison a resolver's cache by guessing it, which is how a whole family of DNS attacks worked.

THREE MORE IDENTIFIERS AND WHAT PREDICTABLE ONES LEAK
  • NTP Reference IDA 32-bit code naming the time source: the IPv4 address, or four octets of the hash of the IPv6 address.
  • Ephemeral port numbersChosen from a counter in most implementations, letting an attacker find a target without seeing traffic.
  • DNS IDA 16-bit identifier copied into the reply, which an attacker guesses to poison a resolver's cache.

§7References